Jabsco flexible impellers can be fitted to most makes and models of bronze flexible impeller engine cooling, bilge, transfer and general purpose pumps.
Jabsco flexible impellers are subjected to rigorous quality processes to ensure reliable, efficient and long lasting performance.
Replace all impellers at least once every year, or sooner, depending on the engine duty. When the installation is correct an impeller may last for several years, but it is always advisable to stick to a schedule of preventative, rather than corrective, maintenance.
Replacing impellers is easy. By removing the end cover screws, it is possible to remove the impeller by using either a Jabsco Impeller Removal Tool, or channel lock pliers, to grip the hub of the impeller. Don?t use screwdrivers as they may damage the face of the pump body, causing leaks, and they can be dangerous in confined spaces.
Always carry spare impellers on board in case of emergency. The impeller is one of the most vital components of the engine cooling system and should always be treated as such.
Always grease new impellers. Firstly, it makes it easier to install the impeller into the pump bore, and secondly it gives added protection to the impeller during initial prime. After replacing the gasket and end cover the pump is ready to use.
Manuals & Downloads: No product manuals available.
In the Box: No product box content available.
Additional Items from Raw Water Pumps | See More Items from Raw Water Pumps Category.
Attwood Sahara Automatic Bilge Pump S1100 Series - 12V - 1100 GPH SKU# 43904 Sahara Automatic Bilge Pump S1100 Series is Attwood's most powerful and efficient automatic pump. High capacity for larger boats and yachts. 1100 GPH at open flow, 973 GPH* at 3.3' head. 1-1/8” hose outlet. One compact yet durable package - pump, wire seals, strainer, and mercury-free switch - and installs quickly and easily in tight spaces. Pumps include 36” lengths of 16-gauge caulked and tinned copper wire. MFG #: 4511-7
Attwood Sahara Automatic Bilge Pump S500 Series - 12V - 500 GPH SKU# 43902 Sahara Automatic Bilge Pump S500 Series. An automatic-switch bilge pump is a requirement for any vessels 20' and over with sleeping accommodations,Compact yet durable package - pump, wire, seals, strainer, and mercury-free switch -and installs quickly and easily in tight spaces. Pumps include 36” lengths of 16-gauge caulked and tinned copper wires. 500 GPH at open flow, 350 GPH* at 3.3' head. Draws only 1.5-amps at open flow! 3/4” I.D. 3-Year Warranty. MFG #: 4505-7
Attwood WaterBuster® Portable Pump - 200 GPH SKU# 43918 WaterBuster® Portable Pump Part #: 4140-4. This patented, submersible pump is a great way to remove unwanted water from boats, pool covers, aquariums and sump pits. Convenient and safe, too, because it needs no electrical cord - runs up to 5 hours on three alkaline D batteries. Excellent for use as a portable pump-out device for paddle boats, inflatables, duck boats, dingies and kayaks. Any craft that lacks a hard-wire, permenent electrical system.
Jabsco 12V Water Puppy SKU# 31419 Water Puppy (US) - Small bilge debris present no problem to these bronze bodied, flexible impeller pumps. Simple design means fewer wearing parts.
ISO 8846 MARINE (Ignition protection). ISO 8849 MARINE (Bilge pump standard). Flow rate: 6.3 USgallons/min).Self-priming from dry up to 1.2m (4ft). Body: Bronze. Impeller: Neoprene. Seal: Lip type.
Voltage: 12 Vdc. Amp Draw: 8 amp. Fuse Size: 15 amp. Motor: Permanent magnet type, fully enclosed. Weight: 4-1/2 lb. MFG #: 18660-0121
Jabsco 36600 Belt Driven Diaphragm Bilge Pump - 12V SKU# 31450 36600 Diaphragm Bilge Pump. 475 usgph open flow output. Self-priming up to 10ft vertical lift, allows mounting above wet bilges. Diaphragm design allows extended dry running. Complete with Pumpgard(TM) strainer. Permanently Lubricated Ball Bearings on Shaft and Connecting Rod. MFG #: 36600-0000
Jabsco Ballast Pump SKU# 51405 Wake/Surf boat Ballast pump is the same one utilized by most major boat builders. Standard with a green Run Dry Impeller. Standard electrical quick connector installed. Connect hoses, mount the pump into the boat, in its orginal position, plug the power leads together and your surfing and wakeboarding again. Impeller # 6303-0007-P - Always Carry a Spare.
Orignial OEM Ballast Pump Replacement. MFG #: 18670-9127
Jabsco Commercial Duty Water Puppy - 12V SKU# 34574 Commercial Duty Water Puppy. Flow rate: 34 litres/min (9 USgallons/min)
Self-priming from dry up to 1.2m (4ft). Small bilge debris present no problem to these bronze bodied, flexible impeller pumps. ISO 8846 MARINE (Ignition protection). ISO 8849 MARINE (Bilge pump standard). Motor Permanent magnet type. MFG #: 18670-0123
Permanent magnet type, fully enclosed, stainless steel shaft, ball type shaft bearing, has adequate torque to reverse the pump